Roll Fast Doors

Roll-fast Economy Doors/Internal

S900–S1000

An economical high speed door that improves productivity and saves money by providing you with...

Improved traffic flow

• – Opening speed of 900mm per second without frequency inverter.
• – Opening speed of 1000mm per second with frequency inverter.

Top air seal

• – Reduces the gap between the building wall and Roll-Fast Door to prevent energy loss.

Reliable performance

• – Even under the most demanding round-the-clock use the Roll-Fast Door cycles completely without fail.

A door moving practically non-stop must also be highly durable

• – The modern frequency inverter control system provides the door with a "soft" start on opening, and a "soft" stop on closing. This means, even in continuous operation, virtually no wear, and as a result, minimum maintenance.

Low maintenance and repair costs

With the Economy Roll-Fast Door, downtime is significantly reduced and repairs, when needed, are quick and easy. The cost of repairing a normal door over one year could actually cover the installation of a Roll-Fast Door. Roll-Fast Doors are easy to clean, retaining that new look.

Service and spare parts

As Roll-Fast Doors are made in Australia, service and spare parts, should they be required, are readily available at all times.

Custom motor

The Roll-Fast Door is powered by a motor specifically designed for these doors.

Control options

Many types of opening and closing controls are available to match your exact requirements.

Economy Roll-Fast Doors are normally produced for internal Opening sizes up to
4000 mm H x 3000 mm W. Larger internal applications upon request.

Roll-fast Doors External

S800

The Robust Vertically Opening Door for Continuous Demanding Operation

For normal external traffic-flow situations: light, friendly and safe

A heavy-duty door with 4 mm thick, fully transparent curtain ensuring safe transport routes and good visual contact. The opening speed of 0.8 m/s is designed for doors up 5000mm H x 6000mm W in normal operation. The tried-and-tested inversion relay control system is entirely sufficient to ensure safe door operation. Fold-out sideframes facilitate maintenance procedures. The operator and shaft are borne by the cantilever sideframes housing the photocell, energy chain and the side tensioning and pull mechanism. Brush seals reduce drafts. When the S 800 is exposed to high wind pressures, we recommend using additional aluminium wind safety profiles to give the curtain the necessary rigidity. By using the wind safety profile, a vinyl panel and fully transparent curtain can also be combined.

Controls

Various types of opening and closing control systems are available to meet individual operational requirements, including induction loop, radio control, radar, photocell, push-button or pull-switch.

Every door is supplied with a programmable controller.

Roll-fast Doors Internal/External

S1100

For quick easy access Reliability and Performance

Performance

Opening speed is 1.1 m/sec. and closing speed is 0.5 m/sec.

Technical details

A self-supporting, easy-to-install construction, consisting of two side guides and a top roller. The top roller is electrically powered and moves the plastic fabric door curtain rapidly up or down. A control box provides operator controls, monitors the door curtain movements and the safety features.

Construction

Galvanized, bolt-on steel sheet side frames with integral guides for the door curtain and integral sealing brushes. Flexible conduit houses power cables to safety edge. Top roll is made, of precision drawn steel tube.

Door curtain

Plastic reinforced fabric 1.5 mm thick, constructed in three sections and separated by aluminium wind bars. Central section is transparent PVC Vision Panel stretching from 1400 mm to 2400 mm above floor. Aluminium bottom rail with self-monitoring safety edge and rubber seal.

Drive

SEUSTER compact electric motor / gearbox combination ready for keying to top roller. Fitted with magneto-electric brake and 6 limit switches mounted directly on the shaft. Drive is mounted right, but can optionally be mounted left. Motor specifications are 240 V, 50 Hz, 16A. Output 0.65 kW, IP 54.

Controls

Controller is equipped with an inverter to ensure fast, smooth operation on acceleration and braking. Any normal pulse generator, time-delay relays or diagnostic LED's may be connected.

Operation

In addition to the OPEN/STOP/CLOSE push buttons mounted on the face of the control box, there is a lockable mains isolator and an emergency stop button. Any of the following may also be incorporated: push buttons, remote control system, pull cords, radar, induction loops, airlock-type controls. Intermediate stop freely adjustable to suit.

Safety

These doors are manufactured and supplied with a self-monitoring safety edge which reverses the door on impact and an anti-crash mechanism. There is a safety photo electric cell mounted within the side frame preventing the door closing if obstructed. An emergency cranking facility is also supplied for opening during power failure.

Roll-fast Doors External/Internal

S1300

The Door with quick manual opening for emergency access

This vertically opening high-speed door really does have it all!

Over and above the structural features of the S 1100 door type, this vertically opening high-speed door boasts a size range up to 5000mm H x 5000mm W and an even higher opening speed of 1.3 m/sec.

Full range of equipment inclusive

Compact direct drive with integral gearbox safety device, electronic limit switches, frequency inverter controls with 7-segment display, function-monitoring, closing edge safety device, photocell to monitor the traffic path and brush seals to reduce drafts and ensure a quiet door action.

Maintenance-friendly

The fold-out sideframes make it quick and easy to carry out maintenance work.

Emergency opening in a matter of seconds

Thanks to the counterbalance weight, the door can be opened by pull rope in no time at all. The counter weight (a standard feature) relieves the operator.

Controls

Various types of opening and closing control systems are available to meet individual operational requirements. Induction loop, radio control, radar, photocell, push-button or pull-switch.

Every door is supplied with a programmable controller.

Roll-fast Doors Internal/Freezer

S1400

When quick access is required the S1400 Internal Roll Fast Door is the answer

Operation

In addition to the OPEN/STOP/CLOSE push buttons mounted on the face of the control box, there is a lockable mains isolator and an emergency stop button. Any of the following may also be incorporated: push buttons, remote control system, pull cords, radar, induction loops, airlock-type controls. Intermediate stop freely adjustable to suit.

Safety

These doors are manufactured and supplied with a self-monitoring safety edge which reverses the door on impact and an anti-crash mechanism. There is a safety photo electric cell mounted within the side frame preventing the door closing if obstructed. An emergency cranking facility is also supplied for opening during power failure.

Technical details

A self-supporting, easy-to-install construction, consisting of two side guides and a top roller. The top roller is electrically powered and moves the plastic fabric door curtain rapidly up and down. A control box provides operator controls, monitors the door curtain movements and the safety features.

Construction

Galvanized, bolt-on steel sheet side frames with integral guides for the door curtain and integral sealing brushes. Top roll is made of precision drawn steel tube.

Door curtain

Plastic reinforced fabric 1.5 mm thick, constructed in three sections and separated by aluminium wind bars. Central section is transparent PVC Vision Panel stretching from 1400 mm to 2400 mm above floor. Aluminium bottom rail with self-monitoring safety edge and rubber seal.

Drive

SEUSTER compact electric motor/gearbox combination ready for keying to top roller. Fitted with magnetoelectric brake and 6 limit switches mounted directly on the shaft. Drive is mounted right, but can optionally be mounted left. Motor specifications are 240 V, 50 Hz, 16A. Output 1.1kW, IP 54.

Performance

Opening speed is 1.4 m/sec. and closing speed is 0.5 m/sec.

Controls

Controller is equipped with an inverter to ensure fast, smooth operation on acceleration and braking. Any normal pulse generator, time-delay relays or diagnostic LED's may be connected.

Hörmann Sectional Doors

SPU40

The Double-Skinned Steel Sectional Door with High Thermal Insulation.

Efficient space usage

Because the M.T.I. Qualos - Hörmann Sectional Doors open vertically, useful space is not wasted around the opening because the door sections are parked underneath the ceiling, parallel to the ceiling or vertically on the wall, depending on the customers requirements.

The right decision for temperature-controlled buildings.

On SPU 40 doors the double-skinned sections are 42mm thick throughout. The strong insulating core of 100% CFC-free polyurethane rigid foam gives the door exceptionally good insulating properties.

Door sections with perfect long-term protection.

Hot galvanised material and the adhering polyester promer coating offer the best possible protection against the adverse effects of the elements. And the additional stucco embossing of the surface makes the door sections considerably less susceptable to damage and wear than is the case with a smooth surface.

Surface: inside and outside in off-white (based on RAL 9002). Other colours to RAL available on request.

Controls

The state-of-the-art operators and controls we offer are manufactured and developed in Hörmann factories throughout Germany.

Reliability.

Perfectly matched components, which have been subject to long duration testing, give you the assurance that your door will perform with absolute reliability.